Water Worker HT14B Gebrauchs- und Pflegehandbuch PDF herunterladen

-1-

What You’ll Need

Before You Start

Always be sure to equip your well system with a proper Pressure

Relief Valve. This should be capable of discharging the full output of

the pump at or below the maximum working pressure of the lowest

rated component in the system. See the owner’s manual for your

pump for output information. This is vital for safe operation of the well

system. THIS PRODUCT COMES WITH A 5 YEAR WARRANTY. SEE

WATER WORKER LIMITED WARRANTY FOR DETAILS.

READ CAREFULLY THE PRODUCT INSTALLATION,

OPERATING AND MAINTENANCE MANUAL.

FAILURE TO FOLLOW THE INSTRUCTIONS AND WARNINGS IN

THE MANUAL MAY RESULT IN SERIOUS OR FATAL INJURY AND/OR

PROPERTY DAMAGE, AND WILL VOID THE PRODUCT WARRANTY.

THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED PROFESSIONAL.

FOLLOW ALL APPLICABLE LOCAL AND STATE CODES AND

REGULATIONS, IN THE ABSENCE OF SUCH CODES, FOLLOW THE

CURRENT EDITIONS OF THE NATIONAL PLUMBING CODE AND

NATIONAL ELECTRIC CODE, AS APPLICABLE.

THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU

TO POTENTIAL PERSONAL INJURY AND OTHER HAZARDS.

OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL

TO REDUCE THE RISK OF PERSONAL INJURY AS WELL AS PROPERTY

DAMAGE.

IMPORTANT GENERAL SAFETY INFORMATION - ADDITIONAL SPECIFIC

SAFETY ALERTS APPEAR IN THE FOLLOWING INSTRUCTIONS.

Failure to utilize a properly sized well tank will result

in excessive strain on the pump and may ultimately

lead to product failure, leaking or ﬂooding or property damage.

For your safety, the information in this manual

must be followed to minimize the rise of electric

shock, property damage or personal injury. Properly ground to

conform with all governing codes and ordinances.

1. If you are installing an entirely new well system, follow Steps II,

III, IV and V. Skip Step I, since you are not removing an existing

tank. However, make sure that the power is turned off before

you hook up the pressure switch to the household wiring. If

you are in any doubt about working with electricity, call a

licensed electrician.

2. If you are replacing a plain steel tank with this Water Worker

diaphragm tank:

a. A diaphragm tank is pressurized with air at the factory (at a

pressure close to that of a car tire). For this reason, it will be

smaller than the plain steel tank, even though both tanks deliver

the same amounts of pressurized water. Because of this, you may

have to adjust the piping to reach the new connections.

b. Install a pressure relief valve at the tank connection to ensure the

safety of the system.

c. If you have a deep well submersible pump, remove all the air

charging devices from the well system (snifter valves, bleeder

oriﬁces, vacuum lines and connection). Then plug the holes

where these devices were located (see your owner’s manual

for location of these devices). These devices are not needed for

pre-charged tanks, and if they are not removed and the holes

plugged, air can get into the well system, cause surges, damage

the system, and impair performance.

d. If you have a jet pump, remove the ﬁttings and plug the

openings where the vacuum or air lines and air volume controls

connect to the pump or piping. If not removed and plugged,

they can allow air into the pipes which can damage the well

system and impair performance.

e. In addition to the above, follow Steps I through V.

3. If you are replacing a diaphragm or bladder style tank with this

Water Worker diaphragm tank:

a. If the two tanks are the same size, follow Steps I through V.

b. If they are different sizes, follow Steps I through V and also adjust

the piping as necessary to accommodate the new size.

4. It is good practice to replace the pressure gauge and the

pressure switch whenever you replace an old tank. Of course,

you can re-use the tank cross assembly if you are replacing a

diaphragm tank with another diaphragm tank (including the tank

cross, pressure gauge, pressure switch, pressure relief valve, pipe

nipple and drain).

a. If you do re-use a tank cross assembly, skip Step II. In this case,

make sure that the tank is installed as closely as possible to the

pressure switch. This will make the system operate as efﬁciently

as possible.

b. If you replace the tank cross assembly with new parts when

you install the new tank, complete all of the steps in these

instructions, Steps I through V.

RELIEF VALVE REQUIRED. A relief valve should

be installed which is set to open at excessive

pressures (75 psig or more). This will protect the well tank and other

system components should the pressure switch malfunction and

fail to shut the pump off. The relief valve should be installed at the

connection of the well tank to the system piping and have a discharge

equal to the pump’s capacity at 75 psig. At least once every 3 years

or if discharge is present, a licensed contractor should inspect the

temperature and pressure relief valve and replace if corrosion is

evident or the valve does not function. FAILURE TO INSPECT THIS

VALVE AS DIRECTED COULD RESULT IN UNSAFE TEMPERATURE OR

PRESSURE BUILD-UP WHICH CAN RESULT IN PRODUCT FAILURE,

SERIOUS INJURY OR DEATH AND/OR SEVERE PROPERTY DAMAGE

AND VOID THE PRODUCT WARRANTY.

5. Always make sure that you equip your well system with an

appropriate pressure relief valve. Whether you are re-using a

tank cross assembly or assembling a new one, check to make

sure that the assembly includes a pressure relief valve that is

capable of discharging the full output of the pump at or below

the maximum working pressure of the lowest rated component

in the system. See the owner’s manual for your pump for output

information. This is vital for safe operation of the system.

INSTALLATION MANUAL FOR VERTICAL WELL SYSTEM TANKS

Models HT14B, HT20B, HT30B, HT32B, HT44B, HT62B, HT86B and HT119B

Keep this manual with the tank for future reference.

Part #: 9015-376 (07/12)

Recommended Tools

Adjustable Wrench

Adjustable Pliers

Pipe Wrench

Hacksaw

Screwdriver

Tape Measure

Tire Pressure Gauge

Tank Water Connection Size 1" NPTF

Pressure Gauge

Relief Valve

Check Valve

Drain Valve

Pressure Switch

Tank Cross (10" Lx1" NPTM)

Teﬂon

Tape

Additional Parts Required (Not Included)

1 2 3 4 5 6 ... 15 16

Inhaltsverzeichnis

Seite 1 - Before You Start

-1-What You’ll NeedBefore You StartAlways be sure to equip your well system with a proper Pressure Relief Valve. This should be capable of

Seite 2 - How to Install the Tank

1400 Division Road, West Warwick, RI 02893 • Téléphone : 401.884.6300 • Télécopieur : 401.885.2567 • www.waterworkerdiy.comProduits couverts : tous le

Seite 3 - EXHIBIT A

-11-Lo que necesitaráAntes de comenzarSiempre asegúrese de equipar el sistema de pozo con una válvula disipadora de presión adecuada. Con esto debería

Seite 4 - IMPORTANT

-12-Cómo instalar el tanquePaso I: Desconecte y retire el tanque existente después de apagar el suministro eléctrico y de drenar el sistema.1.

Seite 5 - LIMITED PRODUCT WARRANTY

-13-Paso IV: Instale el tanque nuevo.1. Instale el tanque nuevo. Colóquelo donde estaba el tanque viejo o sosténgalo en una posición p

Seite 6 - Avant de commencer

-14-IMPORTANTEInstrucciones de seguridad • Asegúrese de leerlas.Este tanque está diseñado para ser usado con agua potable, está limitado a una presión

Seite 7

-15-1400 Division Road, West Warwick, RI 02893 • Tel.: 401.884.6300 • Fax: 401.885.2567 • www.waterworkerdiy.comProductos cubiertos: todos los product

Seite 8 - ANNEXE A

-16-

Seite 9

-2-How to Install the TankStep I: Disconnect and remove the exist-ing tank after turning the power off and draining the system.1. Find the f

Seite 10

-3-Step IV: Install the new tank.1. Install the new tank. Place it where the old tank was or stand it in a position so that you can make the

Seite 11 - Antes de comenzar

-4-IMPORTANTSafety Instructions • Be sure to read.This tank is designed for use with potable water, limited to a maximum pressure of 100 p

Seite 12 - Cómo instalar el tanque

-5-Part #: 9015-376 (07/12)1400 Division Road, West Warwick, RI 02893 • T: 401.884.6300 • F: 401.885.2567 • www.waterworkerdiy.comProducts

Seite 13 - MUESTRA A

-6-Ce dont vous aurez besoinAvant de commencerAssurez-vous de toujours équiper adéquatement votre système pour puits avec une bonne soupape de

Seite 14 - IMPORTANTE

-7-Comment installer le réservoirÉtape I : lorsque vous aurez fermé l'alimen-tation électrique et vidé le système, débran-chez et enleve

Seite 15

-8-Étape IV : installez le nouveau réservoir.1. Installez le nouveau réservoir. Placez-le à l'endroit où se trouvait l'ancien réservoir, o

Seite 16

-9-IMPORTANTConsignes de sécurité • Assurez-vous de les lire.Ce réservoir est conçu pour utilisation avec de l'eau potable et est limité à une pr

Kommentare zu diesen Handbüchern

Keine Kommentare

Water Worker HT14B Gebrauchs- und Pflegehandbuch

Stöbern Sie online oder laden Sie Gebrauchs- und Pflegehandbuch nach Nein Water Worker HT14B herunter. Water Worker HT14B Use and Care Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Water Worker HT14B